a. Power cord unplugged

a. Check that the power cord is plugged in

b. No power to unit

b. Check power at receptacle and fuses

c. Temperature setting too high

c. Lower the temperature setting

d. Low voltage

d. Contact an authorized electrician

e. Incorrect or loose wiring

e. Check all wirings and connections

f. Defrost light blinking

f. Defrost cycle is on

g. Running light blinking

g. Call service at 1-800-777-VINO

a. Adjust the temperature from 55°F to 60°F

b. Check your cooling unit’s owner’s manual and for correct voltage requirements

c. Check the thermistor by placing it in ice water and measuring resistance

d. Check compressor windings, start relay and overload protector

e. Check the condenser fan

f. Clean condenser

g. Call service at 1-800-777-VINO to remove refrigerant

h. Call service at 1-800-777-VINO for OEM information

a. Check your cooling unit’s owner’s manual and for correct voltage requirements

b. Check all wirings and connections

c. Check start relay, start capacitor, overload protector, and compressor

d. Call service at 1-800-777-VINO for OEM information

a. Fan blade bond

a. Check for proper fan blade clearance

b. Incorrect or loose wiring

b. Check all wiring

c. Failed motor

c. Call service at 1-800-777-VINO

a. Evaporator’s airflow is restricted

a. Check for airflow through evaporator

b. Refrigerant is leaking

b. Check for loss of refrigerant

c. Refrigeration system is restricted

c. Call service at 1-800-777-VINO to check for restrictions

a. Check for air restrictions

b. Clean the condenser

c. Defrost the evaporator and reset the temperature

d. Check both fans

e. Check gasket and door opening

f. Check for excessive load or incorrect installation

g. Check power supply

h. Use proper 60 Hz

i. Call service at 1-800-777-VINO if there is loss of refrigerant or restrictions

j. Call service at 1-800-777-VINO to add or remove refrigerant

a. Incorrect fuse or breaker

a. Check for proper fuse or breaker

b. Incorrect wiring

b. Check all wirings and connections

c. Failed components

c. Call service at 1-800-777-VINO

a. Wine-Mate unit’s mounting area is not secure

a. Add support to improve installation

b. Loose parts

b. Check fan blades, bearings, cabinet washers, tubing contact and loose screws

c. Compressor overloaded due to high ambient temperatures or airflow restriction

c. Check for airflow blockage

d. Malfunctioning components

d. Call service at 1-800-777-VINO

a. Ensure the humidity is set between 50-70%
b. Immediately wipe up spills as they occur
c. Empty the cabinet and thoroughly clean it. If you have a large mold infestation, it is recommended you consult a mold remediation professional.
d. Put on safety goggles and a dust mask. If you have family members with asthma or mold allergies, make sure they are not nearby while you work.
e. Vacuum the moldy wood with a HEPA-filter vacuum, using the brush attachment if it has one. This removes any loose spores and bits of mold that might otherwise enter the air while you clean the wood.
f. To remove the remaining mold, use one of the following methods:
     1. Add a 3% hydrogen peroxide solution to a spray bottle and saturate the surface of the racks to kill the mold and spores. Let it sit for 15 minutes then gently scrub the surface using a clean, soft cloth.
     2. Add distilled white vinegar to a spray bottle and saturate the surface. Let it sit for 60 minutes then gently scrub the surface using a clean, soft cloth.
     3. Mix 1 tbsp of baking soda with warm water in a spray bottle and saturate the surface. Gently scrub the surface and wipe with a clean, soft cloth.
     Note: Do not use anything containing bleach or chlorine.
g. Once the mold has been cleaned, point a fan at the racks to allow them to dry thoroughly.
h. Should the mold return after completing the steps above, Call service at 1-800-777-VINO to have your unit thoroughly inspected.

a. Ensure the door to be closed and locked, so that it is sealed.
b. If there is a gap of air, condensation and dripping will happen.